Multiple Electrolytes and Invert Sugar Injection Type 3
»Multiple Electrolytes and Invert Sugar Injection Type 3is a sterile solution of a mixture of equal amounts of Dextrose and Fructose,or an equivalent solution produced by the hydrolysis of Sucrose,and suitable salts in Water for Injection to provide sodium,potassium,chloride,and ammonium ions.It contains not less than 90.0percent and not more than 110.0percent of the labeled amounts of sodium (Na),potassium (K),ammonium (NH4),and invert sugar (C6H12O6),and not less than 90.0percent and not more than 120.0percent of the labeled amount of chloride (Cl).It may contain Hydrochloric Acid or Sodium Hydroxide used to adjust the pH.It contains no antimicrobial agents.
Packaging and storage— Preserve in single-dose glass or plastic containers.Glass containers are preferably of Type Ior Type IIglass.
Labeling— The label states the content of each electrolyte in terms of milliequivalents in a given volume.The label states the total osmolar concentration in mOsmol per liter.When the contents are less than 100mL,the label alternatively may state the total osmolar concentration in mOsmol per mL.
Identification—
A: It responds to the Identificationtest under Invert Sugar Injection.
B: It responds to the flame tests for Sodium á191ñand Potassium á191ñ,and to the tests for Chloride á191ñand Ammonium á191ñ.
Pyrogen— It meets the requirements of the Pyrogen Test á151ñ.[NOTE—Dilute,with Water for Injection,Injection containing more than 10%of invert sugar to give a concentration of 10%invert sugar.]
pHá791ñ: between 3.0and 5.5.
Completeness of inversion—
Mobile phase ,Standard preparation,and Chromatographic system—Prepare as directed in the test for Completeness of inversionunder Invert Sugar Injection.
Test preparation— Transfer an accurately measured volume of Injection,equivalent to about 2.5g of invert sugar,to a 100-mLvolumetric flask,dilute with water to volume,and mix.
Procedure— Proceed as directed for Procedurein the test for Completeness of inversionunder Invert Sugar Injection.Calculate the quantity,in mg,of sucrose in the volume of Injection taken by the formula:
100C(rU/rS),
in which the terms are as defined therein.Not more than 1.5%of the quantity of invert sugar in the volume of Injection taken,based on the labeled amount,is found.
Other requirements— It meets the requirements under Injections á1ñ.
Assay for potassium and sodium—
Internal standard solution ,Potassium stock solution,Sodium stock solution,Stock standard preparation,and Standard preparation—Prepare as directed in the Assay for potassium and sodiumunder Potassium Chloride in Sodium Chloride Injection.
Assay preparation— Transfer 5.0mLof Injection to a 500-mLvolumetric flask,dilute with Internal standard solutionto volume,and mix.
Procedure— Proceed as directed for Procedurein the Assay for potassium and sodiumunder Potassium Chloride in Sodium Chloride Injection.Calculate the quantity,in mg,of potassium (K)in each mLof the Injection taken by the formula:
C(RU,766/RU,671)(RS,671/RS,766),
in which the terms are as defined therein.Each mg of potassium is equivalent to 0.02558mEq of potassium.Calculate the quantity,in mg,of sodium (Na)in each mLof the Injection taken by the formula:
C(RU,589/RU,671)(RS,671/RS,589),
in which the terms are as defined therein.Each mg of sodium is equivalent to 0.04350mEq of sodium.
Assay for chloride— Using the Injection,proceed as directed in the Assay for chlorideunder Multiple Electrolytes Injection Type 1.
Assay for ammonium— Using the Injection,proceed as directed in the Assay for ammoniumunder Multiple Electrolytes and Dextrose Injection Type 3.
Assay for invert sugar— Using the Injection,proceed as directed in the Assay for invert sugarunder Multiple Electrolytes and Invert Sugar Injection Type 1.
Auxiliary Information— Staff Liaison:Karen A Russo,Ph.D.,Scientist
Expert Committee:(PA1)Pharmaceutical Analysis 1
USP28–NF23Page 726
Phone Number:1-301-816-8379
Return